E-Mu SP-12 Manual do Utilizador descarregar pdf (Página 20)

Messages And Errors SP-12 Librarian User’s Manual

Page 20

Water’s Edge Software

Cassette/Disk

NoDisk Connected

This message appears only on the SP-12’s control panel. The SP-12 is

not communicating with the SP-12 Librarian. Make sure your MIDI network

is set up as described on page 2, check the MIDI cables, make sure the

SP-12 Librarian application is running, make sure that the relevant file is

open on the Macintosh and that the “SP-12 Link” window is open.

If you are running a low-end Macintosh, such as a Macintosh Plus with

only floppy disks, then you may have problems having the

SP-12 Link

open automatically when a command is entered at the SP-12 (see

Preferences). When you enter a command at the SP-12’s control panel, it

sends a “disk status” command to the SP-12 Librarian. If the librarian does

not open the link and return a status to the SP-12 quickly enough, then the

SP-12 assumes that no disk is connected. If this happens, re-try the

command at the SP-12’s control panel and the link will be established.

Changes made to Categories were not saved because the “SP-12 Librarian”

application was moved or renamed

Changes made to Preferences were not saved because the “SP-12 Librarian”

application was moved or renamed

Changes made to Preferences and Categories were not saved because the

“SP-12 Librarian” application was moved or renamed.

Changes made to the Preferences settings and/or the Categories List

were not saved because the SP-12 Librarian application was renamed or

moved to another folder while it was running. This can occur only when

using MultiFinder or System 7.

You can avoid this problem by not renaming or moving the SP-12

Librarian to another folder while it is running.

Checking disk status.

The SP-12 Librarian is checking the active window’s file and the disk on

which it is located. This information is passed back to the SP-12.

Disk cannot be formatted from the SP-12.

SP-12 command “30” (format disk) was issued from the SP-12. The

SP-12 Librarian does not accept this command. If you want to create a

new file, use the File menu’s

New

command.

Disk is full -- No room for work file.

An existing sound file or sequence file can’t be update because there is

not enough available space to create a work file. This process is explained

under

“Fail Safe” File Management

in the

Behind The Scenes

chapter.

You can get around this problem by copying the required file to a blank

disk. Update that copy with the SP-12’s data, then move the copy back to

the original disk.

Disk is full! Save songs on another disk.

The disk was filled while saving sequence data in a blank or damaged file.

The file is now considered damaged and contains no valid data (although

it may occupy a fair amount of space on the disk).

Save your song data on another disk, then quit the SP-12 Librarian and

delete the damaged file.

Disk is full! Save sounds on another disk.

The disk was filled while saving sound data in a blank or damaged file.

The file is now considered damaged and contains no valid data (although

it may occupy a fair amount of space on the disk).

Save your sound data on another disk, then quit the SP-12 Librarian and

delete the damaged file.

Disk is full. Please save “File Name” on a different disk.

The file, whose name is indicated by

”File Name”

, could not be saved

because the disk is full. Save the file on another disk using the File

menu’s

Save As

command.

File name can't contain a colon (:)

Do not use a colon (:) when entering a file name.

File name must be between 1 and 31 characters long.

The file name you entered exceeded 31 characters in length. A file name

must be from 1 to 31 characters long, including spaces.

Insufficient memory to add new category.

There is not enough memory available to create a new sound category.

This problem will occur only when memory is severely limited.

Close any open desk accessories and try again. If this doesn’t work, quit

the SP-12 Librarian. If you are not using MultiFinder or System 7 and disk

caching is on, turn it off (via the Control Panel desk accessory). If you are

using MultiFinder or System 7, allocate more memory to the SP-12

Librarian, restart the SP-12 Librarian, and try the operation again.

Insufficient memory to add new category. Try closing a window first.

There is not enough memory available to create a new sound category.

This problem will occur only when memory is severely limited.

Close any open desk accessories. If possible, close a document window

that you do not immediately require and try the operation again. If you get

the same problem, quit the SP-12 Librarian. If you are not using

MultiFinder or System 7 and disk caching is on, turn it off (via the Control

Panel desk accessory). If you are using MultiFinder or System 7, allocate

more memory to the SP-12 Librarian, restart the SP-12 Librarian, and try

the operation again.

Insufficient memory to add sounds to catalog.

There is not enough memory available to add the active sound file to the

Sound Catalog. This problem will occur only when memory is severely

limited.

Close any open desk accessories and try again. If this doesn’t work, quit

the SP-12 Librarian. If you are not using MultiFinder or System 7 and disk

caching is on, turn it off (via the Control Panel desk accessory). If you are

using MultiFinder or System 7, allocate more memory to the SP-12

Librarian, restart the SP-12 Librarian, and try the operation again.

Insufficient memory to add sounds to catalog. Try closing a window first.

There is not enough memory available to add the active sound file to the

Sound Catalog. This problem will occur only when memory is severely

limited.

Close any open desk accessories. If possible, close a document window

that you do not immediately require and try the operation again. If you get

the same problem, quit the SP-12 Librarian. If you are not using

MultiFinder or System 7 and disk caching is on, turn it off (via the Control

Panel desk accessory). If you are using MultiFinder or System 7, allocate

more memory to the SP-12 Librarian, restart the SP-12 Librarian, and try

the operation again.

Insufficient memory to complete operation.

There is not enough memory available to complete the required operation.

This problem will occur only when memory is severely limited.

Close any open desk accessories and try again. If this doesn’t work, quit

the SP-12 Librarian. If you are not using MultiFinder or System 7 and disk

caching is on, turn it off (via the Control Panel desk accessory). If you are

using MultiFinder or System 7, allocate more memory to the SP-12

Librarian, restart the SP-12 Librarian, and try the operation again.

Insufficient memory to complete operation. Try closing a window first.